Peugeot 208 Key Replacement

(Image: https://www.thekeylab.co.uk/wp-content/uploads/sb-instagram-feed-images/310300814_438157535072560_441431797686435441_nlow.jpg)Peugeot 208 key replacement is best left to professional auto locksmiths with the right equipment and technical knowledge. They can design and program keys quicker and more efficiently than dealers.

A dead coin battery is most likely to blame the reason why your key fob isn't locking or unlocking doors. However, there are many other reasons that the key may be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your peugeot 3008 key programming 208 from locking and unlocking, as well as stopping it from starting the engine. In this case, you will need to use the alternative starting method found in your vehicle's owner's manual.

Another reason why your 208 might not start is because the spark plugs are worn down. The spark plugs are responsible for instigating the fuel which starts the engine. However they have a short lifespan. If they are not used enough they will eventually fail.

Luckily, there's an easy solution for this problem. The best solution is to measure the voltage of your car battery with a multimeter. If the voltage falls below 11,5 volts, it's the time to replace it. It is also important to clean the contacts of the battery when it has corrosion. This can be done by removing the rubber cover from the two battery terminals, and then using a wirebrush to eliminate any damaged parts of the battery. Then, you should connect your cables to connect the positive and negative poles.

Water Damage

If your 208 doesn't start and the battery isn't flat, then you need to make sure that the spark plugs work. It could be that they are overly filthy, making them unable to spark. This can be fixed easily by cleaning the spark plugs in a workshop.

peugeot car keys replacements cars are equipped with a key with a transponder compatible with the immobiliser. This ensures that only a valid key can turn the engine. If the chip in the peugeot key Repair key is damaged, it will not send the proper signal to the vehicle.

This is a very common issue that can be caused by water damage. This is particularly prevalent in colder climates where the vehicle might have been exposed to rain or snow. If this is the case, you should seek out a reputable auto locksmith who has all of the tools and equipment needed to reprogram the new key. They will also have the most up-to-date technological know-how and the equipment required to create the Peugeot 208 smart key. The process shouldn't last more than 15 minutes.

Contacts to the battery are not working properly.

Peugeot changed from the carbon-encased transponder chips and introduced a new type of chip that incorporates electronic components that are placed on a circuit board. This new technology works great when it's brand new however, over time, the circuit boards start to degrade and stop working properly.

This could prevent the immobiliser from working, so your vehicle won't start. Contact a Peugeot specialist or a locksmith if this is the situation.

Another issue that is common is when the battery of the key fob starts to die, this causes the blade of the key to stop being able to feed into the lock. A locksmith for cars will replace the battery and then cut a new blade for you. This is a simple solution.

Faulty Receiver Module

(Image: https://www.thekeylab.co.uk/wp-content/uploads/2022/06/KeyLab-1-e1658690716312-300x146.png)If your Peugeot key fob isn't working after dropping it on the floor, getting exposed to a sudden downpour or accidentally washing it or washing it, it could be due a malfunctioning receiver module. The receiver is responsible for transmitting radio frequency signals to the on-board computer, which is responsible for controlling the centralized locking system in your Peugeot vehicle.

Rubber seals on the key fob stop water from getting to the electronic chip. However, prolonged exposure to water can be able to penetrate these seals and cause damage to the chip. The high salt content of the ocean or pool could cause damage to the key fob, especially if it is submerged.

The module needs to be replaced if the Peugeot spare key is no longer working. This is only done by a peugeot 406 key fob specialist or an expert auto locksmith. Peugeot keys are, unlike other vehicles, are protected by an immobilizer system. This requires the correct code to begin the car. It is for this reason that you should only rely on the Peugeot locksmith to design and program a replacement.

Faulty On-Board Computer

The computer on board of your Peugeot is responsible for a variety of systems in your car, including airbags and power windows. If something is wrong with these systems, they will usually display a code that indicates the issue. The code will be stored in the system until the issue is fixed. Usually, this will mean replacing the onboard computer.

One of the most frequent reasons for the airbag light coming on is loose or corroded connection in the airbag sensor. This could be due to wear and tear, aging or exposure to moisture and salt. This issue should be addressed as soon as you can, since an airbag malfunctioning could pose a risk in the event in the event of an accident.

If your Peugeot is showing a card not detected error, the battery inside the key fob may be dead or weak. This could prevent the key fob from sending a signal that disarms your vehicle's standard immobilizer. Try this by pressing the unlock key on the fob's key and then trying to start your vehicle. If this fails it is likely that the battery needs to be replaced.