Patio Door Lock Repairs

Over time, the wear and tear can cause lock malfunctions. There are a few basic steps you can follow to ensure the security of your upvc patio door repairs near me door.

These simple fixes can make your home safer no matter if you adjust the lock or clean the mechanism.

Clean the Lock

Although patio door repair doors are an excellent way to let in the outside and keep out the elements but they can also pose a security risk in the event that your lock isn't operating as it should. With time, wear and tear, hot and cold weather, dirt, and debris can cause your patio door lock to become difficult to operate. With a little care you can ensure that the lock on your patio door is always working properly.

(Image: https://www.repairmywindowsanddoors.co.uk/wp-content/uploads/2018/09/Replacement-Windows-150x150.jpg)In the beginning, it's essential to clean your patio door's lock and all its moving parts. This helps flush out any accumulated grime and coatings that could hinder the lock from working in the way it should. Begin by wiping down the moving parts of the lock for your patio door with a damp, clean cloth. then use a scouring pad or rough damp cloth to scrub any hard-to-reach parts of the door and frame that are ingrained with dirt. Then, wipe the entire lock with a dry cloth to remove any remaining dampness and let it to air dry prior to making use of it again.

If you have a patio door that uses a pin tumbler latch mechanism You can grease the lock by applying graphite powdered to the key or applying a Teflon-based lubricant like WD-40 Multi-Use. This type of lubricant can be easy to apply, and doesn't break down with time. If you're unable to find the correct lubricant for your lock, make use of a pencil with a more of a thicker tip. Place the pencil into the lock, and shake it around to spread the graphite.

Regular maintenance is also required to keep the tracks of sliding patio doors free from dirt, dust and debris. They are particularly susceptible to ice, snow, and other debris, which could cause them to jam or bind. This can make it difficult for your patio door to be opened and closed.

You can clean the track rails and rollers of sliding patio doors by removing any weather stripping that is damaged or dirty. Clean it and replace it. Patio door rollers can also be cleaned and sprayed with an oil that is nonstick.

Lubricate the moving parts

uPVC French Doors, like sliding patio doors repairs patios, are operated by using 3 to 4 or occasionally 5 points locking mechanisms. They include the lock cylinder and handle that is operated with a key. They also require maintenance, and specifically lubrication of the moving parts. This can be done using an oil that is thin (never WD40) and should be done every year.

If sagging hinges don't cause the problem, it could be that the door is not aligned. It could be rubbing or catching against the strike plate's opening in the frame. Remove the strike plate and employ a sharp tool enlarge the mortise. This lets the latch sit properly in the hole and avoids scratching or catching on the frame.

Once the cylinder is cleared of the way and out of the way, measure its width using the help of a book or piece wood that can fit into the gap of adjustment screw above the lock. The outer dimension is measured from the outside of the door to the center of cylinder. The inner dimension is measured from the center adjustment screw until the end cylinder.

Check the lock's width

If your patio door latch isn't able to turn, even after cleaning and lubricating, it's possible that it's out of alignment with the strike plate hole. Verify that the door is properly balanced and that the hinge screws are tight. In a lot of cases, moving the strike plate upwards or downwards can solve the issue.

Oftentimes, the problem occurs when the lock's strike is too small for the latch to engage. In this instance, you can widen the opening with an hammer and chisel. Then test the latch to ensure that it doesn't touch the jamb frame of the door or get caught the frame.

Before purchasing a new lock, you should first identify the type of mortise lock you currently have. This can be done by looking at the faceplate on the lock and determining if it is round or square. Then, look at the screw holes on the current lock and note the size of each one. This will enable you to locate an alternative lock that is exactly the same width and fits into the hole that you already have.

In addition to identifying the mortise lock that is currently in use, you'll also need to check it for any scratches or bends that might require repair. A damaged or bent latch is more likely than one that's frequently used to break. Replace the lock if it displays evidence of damage.

After you've determined the type of lock replacement you require, it's now time to begin the actual repair. Take the old handle and spindle out of your patio door, and then insert the new one. Start by putting in the handle inside and aligning it with the spindle, and then fixing it with the two screws or bolts which hold it. Once the handle in the interior is installed, you can install the handle that is outside and screw it in place, too. After you've completed these steps, test the handles to make sure that they open and shut easily and that the latch engages correctly with the strikeplate.

Check the door's Strike

The door latch and strike plate are two parts of the lock that work to ensure that the latch locks the door. A misaligned strike plate or door latch will cause the latch to not latch the door in a proper manner. Fortunately, this issue is usually simple to fix.

Examine the holes that receive the strike plate to make sure they are clear of obstructions, such as dirt or plastic plugs. Then, loosen the keeper screws that keep the strike plate in place and allow it to move vertically but not removing it from the frame of the door. Adjust the strike plate so that it aligns its holes for receiving with the latch hooks of the door latch. After the strike plate has been adjusted tighten the screws, and then test the door to determine whether it locks smoothly after the new adjustment.

Door strike plates can be a bit difficult to access for homeowners with sliding patio doors, but they're crucial for locking and unlocking your door. These metal plates are located on the top and bottom jambs of the door where they serve as the support for the latch. The door latch is able to slide into the strike plate to form an airtight seal when closed. If the strike plate is damaged, rusted, or not properly installed, it could prevent the latch from locking the door securely.

A misalignment between the strike plate and latch is the most common reason for the patio lock not to close or stick. This can be checked with the ”lipstick” test. Apply some lipstick across the edge of the deadbolt. Then cover it with masking tape. When you shut the door the lipstick will leave a mark on the tape, indicating you exactly where the latch meets the strike plate. If the mark is too high or low it is possible to adjust the strike plate.

The sliding patio door locks protect your home from burglars, and if they're not working correctly, you should fix the problem quickly. Follow these simple steps to fix your Local Patio Door Repairs door lock and restore it's function.