(Image: https://www.thekeylab.co.uk/wp-content/uploads/sb-instagram-feed-images/308785165_499195788347328_5859105632268553197_nlow.jpg)Peugeot 208 Key Replacement
It is best to leave the replacement of Peugeot keys 208 to auto locksmiths who have the equipment and expertise. They can design and program keys faster and cheaper than a dealership.
A dead battery for your coin is most likely to blame if your key fob stops locking or unlocking the doors. There are many other reasons that the key might be malfunctioning.
Dead Coin Battery
A dead battery can stop your Peugeot 208 from locking and unlocking, as well as hindering it from starting the engine. In this case you'll have to use the alternative starting method found in your vehicle's owner's manual.
The spark plugs can also be worn out. The spark plugs ignite the fuel to start the engine. They only last for a certain amount of time. If they aren't utilized enough and they fail, they'll eventually die.
Luckily, there is an easy solution to this issue. Examine the voltage of your battery with a multimeter. If it is below 11.5 Volts it is time to replace it. If the battery is damaged it is crucial to clean its contacts. You can do this by lifting the rubber covers that protect the two terminals on the battery and using wire brushes to clean any parts that are corroded from the battery. Then, you must reconnect the positive pole cables to the negative.
Water Damage
If your 208 does not start and the battery has not been replaced, you must look at the spark plugs. It could be that they are simply too dirty and don't spark. This is easily fixed by cleaning the spark plugs in a workshop.
Peugeot cars use a key with a transponder compatible with the immobiliser. This ensures that only the correct key is able to turn the engine. If the chip inside the Peugeot key is damaged then it won't send the correct signal to the vehicle.
Water damage is a typical reason for this issue. This is a common problem in warmer climates where the vehicle has been exposed to snow or rain. If this is the case, get in touch with a reputable locksmith who has all the tools and equipment required to reprogram the new key. They will also have the latest technology and equipment needed to create a Peugeot 208 smart key. The process shouldn't last more than 15 minutes.
Faulty Battery Contacts
Peugeot changed from the old carbon encased transponder chips and shop introduced a new type of chip that incorporates electronic components in circuit boards. This new technology works great when it's brand new but over time the circuit boards begin to wear out and stop functioning properly.
This could stop the immobiliser from triggering so that your vehicle won't start. Contact an peugeot partner van key fob specialist or a locksmith if this is the case.
A common problem is when the battery inside the key fob begins to die. This causes the blade of the key to stop feeding into your lock. A car locksmith will replace the battery and cut a new blade for you. This is a quick solution.
Faulty Receiver Module
If your peugeot key replacement key fob has stopped working after dropping it on the floor, or being exposed to a sudden rain or accidentally washing it, it could be due to a defective receiver module. The receiver is responsible for transmitting radio frequency signals to an on-board computer, which controls the central locking system of your Peugeot vehicle.
Rubber seals on the key fob stop water from getting to the electronic chip. The chip can be damaged by water in the event that it is exposed water for a long time. Submerging the key fob into the ocean at the beach or throwing it into the water can be particularly damaging due to the high salt content.
The module needs to be replaced if the Peugeot spare key isn't working anymore. This can only by done by a Peugeot specialist or a professional auto locksmith. Peugeot keys, unlike other cars, are protected by an immobilizer system. This requires the right coding to start the car. This is why it is imperative that you should only rely on the Peugeot locksmith to design and program an alternative.
Computer on-board is not working properly
The computer on board of your peugeot partner key fob programming is responsible for many of the systems inside your car, including airbags and power windows. When something goes wrong in these systems, they will usually display a code that identifies the issue. The code is stored within the system until the problem is resolved. Usually, this will mean replacing the on-board computer.
One of the main reasons for the light turning on is the loose or corroded connection in the airbag sensor. This can be caused by wear and tear, aging, or exposure to moisture and salt. It is imperative to have this issue addressed as soon as you can, since an airbag that is not functioning properly could be dangerous in the event an accident.
If you notice a card not found error on your Peugeot, the key battery inside the key fob may be weak or dead. This could prevent the key fob from sending a signal that disables the standard immobilizer in your vehicle. Test this by pressing the unlock button on the key fob and then trying to start your car. If this does not work then the battery in the key fob is in need of replacement.