Fiat 500 Replacement Key Fob

If your remote key fob has stopped working, it may be time to replace the battery. However, if you replace the battery and it does not work, then the problem is probably elsewhere.

United Locksmith specializes in the production of new keys for classic vehicles. We have the tools and components needed for this job.

Dead Coin Battery

A dead battery is the primary cause of your fiat key programming 500 keyfob (made my day) not locking or unlocking the doors. The key fob has an in-built battery that can quickly deplete in the event that it is not used often enough. If your remote started to show signs of weakening such as a loss of range or stopped working completely it is likely that the battery is dead.

Metal clips hold the battery securely on the key fob. If the clips aren't tight enough, they could cause problems with contact, which can prevent your remote from receiving power. Use a flathead screwdriver to open the retaining clips and then remove the old battery. Use a battery that has the same voltage, size and specification as the original.

The key fob could be damaged or corroded due to exposure to water. Even a quick bath in soapy water may harm the electronic chip within. It's best to keep your key fob in a dry place.

Water Damage

Water damage may be the reason behind your key fob not working properly. Key fobs have rubber seals that prevent them from being damaged by rain or a splash of water, however it is crucial to keep your car keys from being tossed into the pool, ocean and the washing machine!

The key fob has an electronic chip inside that transmits a signal to your car's immobilizer system. This is the reason why your 500 can lock or start, but should the chip become wet, it will no longer function.

If you're trying to determine if your key fob is functioning You can clean the internal electronics using isopropyl or electronic cleaner. It is recommended to replace the key fob when it's submerged in salt water instead of trying to fix it yourself.

(Image: https://www.thekeylab.co.uk/wp-content/uploads/sb-instagram-feed-images/311159893_995841588058766_6213964028136182559_nlow.jpg)A replacement fob can cost you a few dollars however, it's cheaper than having to have your fiat ducato key fob 500 towed to a dealership and fixed there! You can also make it yourself by following only a few steps. Be sure to have the correct battery type before attempting to open your key fob. This task is much easier than it looks and you can find step-by-step instructions online for virtually any key fob in your car.

Faulty Chip

The chip in the key fob communicates directly with the immobiliser of your spare car key fiat 500 to ensure that the vehicle will only start when the correct keys are inserted. If the chip is damaged or corrupted in any way your car will not start.

Damage to the water or a dead phone battery are among the most frequent causes of defective chips. It is recommended to leave the job to a professional locksmith who can replace the chip in a short time and at a reasonable cost.

If your key fob stops functioning after exposure to clean water from the tap or rain, remove the battery and clean the electronic component with a tissue to ensure that it is completely dry before putting it back in. If the key fob does not function, there is an opportunity that it is a fried component and needs to be replaced.

Many people will seek out their dealer when they are in need of an entirely new Fiat key fob, however it can be a expensive option. United Locksmith is the best option for you if need your Fiat key fob repaired at a reasonable cost. We have the tools and knowledge necessary to fix your Fiat key fob in a quick and professional way.

Faulty Receiver Module

Fiat key fobs send a signal up 50 feet to the vehicle, which will unlock and close the doors (and start the vehicle for vehicles with automatic transmissions). However, there are several things that could cause the fob to cease working. These include a dead coin battery damaged by water buttons, worn ones, a receiver module issue, and signal interference or an electronic chip that is malfunctioning.

If the fob was placed in an area that has experienced severe trauma (such as being dropped onto the floor or washed in the washer) the fob may not be in a position to communicate with the Body Control Module (BCM) of the car. This is because the BCM is an extremely secure system that will only accept signals from a genuine key and not accept any other.

It is necessary to replace the fob if this happens. A locksmith professional can handle all aspects of the key replacement procedure as well as programming a new one for the 500. They can even provide you with an clone fob that performs the same as the original (and costs just less than the cost).