Reasons Your fiat key replacement cost 500 Key Fob Won't Work

(Image: https://www.thekeylab.co.uk/wp-content/uploads/sb-instagram-feed-images/310762719_174097598533869_2015889089625884380_nlow.jpg)A key fob from fiat 500 new key 500 makes it simple to open doors and start your car. However, there are many reasons why the key fob might stop functioning. These include a dead battery or water damage, receiver module issues, or interference.

This listing is for a NEW replacement Fiat Van Key Replacement Flip Key Remote that is similar to the Ilco brand. It needs to be professionally programmed (click here to find local locksmiths in the automotive industry). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most common reason the 500 key fob won't function is the battery is dead. Modern key fobs have a limited range of operation and must be within a few inches of the vehicle in order to work. If you're far from your vehicle and press the key fob button, the car will not respond, and will display a ”Key Fob Not Detected” message in the instrument cluster.

If this happens, simply replace the battery of your coin cell (Part number CR2032) with a brand new one from a reliable brand like Panasonic, Duracell, or Energizer. You can find them in the local hardware store or on the internet.

After you've replaced the battery in the coin cell, you can test it by standing near your fiat punto locked keys in car 500 and pressing the buttons. The car will blink its parking lights and the key fob should be able to operate the lock and unlock buttons.

If the fob's key doesn't function after replacing the battery, it might be damaged by water, which prevents it from connecting to the receiver module in your car. Water damage can occur in a variety of ways, such as the simple splash or submerging the key fob into saltwater at the beach. If you suspect your fob was exposed to water, put it in a dry rice bag to pull the moisture back out. If that doesn't work your fob is likely to need to be reset by an experienced auto locksmith or dealer.

Water Damage

Although the fob is equipped with rubber seals that keep water from the electronic chip inside the device, submerging it into the ocean or washing it in a machine can cause water damage. Saltwater poses a particular risk to the fob's circuit board which causes it to short out and eventually end up dying. The fob getting wet is not an ideal idea but if you accidentally drop it in a cup of water or forget to remove it from your pocket before you run the washing machine, don't give up hope.

First, remove the battery from the fob. Before replacing the battery, clean the electronic chip with isopropyl or similar products. Next, test the fob to verify if it is working. If the fob doesn't work then it might need to be changed. This is typically done by a professional or dealer auto locksmith.

If your key is old and has not been programmed to work with your vehicle it is necessary to replace it completely. This is a simple procedure that can be carried out by a professional automotive locksmith. The locksmith will require the key to be cut to match your car's ignition. They will also need to reprogram the fob in the system of your car. This is an affordable and quick procedure that can be completed in the same day.

Receiver Module Issues

One of the most common reasons why your 500 key fob might stop functioning is because it's out of range. The remote typically has an area of 30 feet or less, and if it's too far away from your car it will not respond to your commands. This can be fixed by moving it closer to your vehicle until it starts responding.

If you've replaced the coin battery (commonly called a ”button” or ”watch”) and your fob doesn't function, it could have an internal circuit board issue. In most cases, reprogramming the fob will resolve this problem. You can find the instructions on how to start a fiat 500x with key to do this for most vehicles by searching YouTube or consulting the owner's manual.

It may be necessary to replace the metal clips that hold the coin batteries in their place. If they lose tension it may prevent your battery from being properly seated, causing your remote to malfunction.

In rare cases the fob may be out of the vehicle's sync because of software or hardware problems. This could be a huge headache, but you can usually fix it by visiting an auto locksmith to have them reprogram your fob. In certain situations, they may need to reinstall the program in your body control module, as well.

Interference

Interference can also cause the key fob not to receive or transmit the signal. This can occur when the key fob is in close proximity to a radio transmitter like a cell phone or radar detector. The key fob could not function because of a weak connection with the buttons or water damage, or damage to the internal chips.

If your key fob suddenly stopped working, or you've tried everything at home to fix it (e.g. replacing the battery, reprogramming, and using the spare key fob, it could have a malfunctioning receiver module on your 500. The receiver module, which is located beneath the dashboard, picks up radio frequency signals from your key fob. It converts the signals into electronic commands that are then read by the vehicle.

There is a simple way to reset the 500's onboard system including the keyfob. Disconnect the battery for 15 minutes by removing first the negative cable, then the positive cable. Reconnect the battery. This will eliminate any remaining electricity, and restart the computer in your car. This can help get your key fob to function again. If the issue continues, you should consult an expert technician. They can identify the exact cause of any problems.