(Image: [[https://g28carkeys.co.uk/wp-content/uploads/2023/10/Porsche-New-2023.png|https://g28carkeys.co.uk/wp-content/uploads/2023/10/Porsche-New-2023.png]])How to [[https://auto-locksmiths55291.tusblogos.com/29758503/15-audi-replacement-car-keys-bloggers-you-must-follow|replace audi key fob]] an Audi G28 Engine Speed Sensor Charles the Humble Technician shows how to replace the G28 Engine Speed Sensor. This sensor is located at the top of the transmission just above the flywheel ring gear. It sends a message to the ECU via a grey wire T55/49, then to the tachometer located on the instrument cluster. 1. Engine Speed Sensor Located on the edge of the transmission above the flywheel ring gear the G28 Engine Speed Sensor sends signals to ECU pin T55/49 through a grey wire. The ECU utilizes this information to regulate boost and fuel. It also sends signals to the G5 tachometer inside the instrument cluster. The sensor is used to link the G40 Camshaft position Sensor. The ecu must know when the crankshaft is TDC and where the camshaft is so it can trigger spark and injectors according to the situation. If this sensor fails to function, the ECU will display an error code P00160. This indicates that the Crank Shaft is out of line with the Intake Camshaft. It could also be a sign of a chain stretch or a jump in the chain link of the upper chain of timing. The code won't appear without the additional information supplied by other sensors (G4 or G40). Testing is a bit challenging because there are two connector pins and they serve different purposes however the best way to test it is by measuring resistance between the sensor and the ECU. It should read about 1000 ohms when it is operating at its maximum. If you are having problems with this part, check for evidence of coolant or oil in the connector bay. 2. Injectors Yesterday, as i was accelerating off the highway paytoll at a high speed, i noticed a huge decrease in power. It was as if the engine was running out of gas. Or my injectors were not firing. I pulled out the spark plugs this morning, three were soaked with gasoline and the fourth was unclean. When i crank the engine without sparks i put tissue on top of each injector hole, the 3 drenched with gazoline pop out, but the 4th stays closed. I tested the ground connection of ECU pins 14,30, and 48/55. I found zero ohm. I'm assuming that the issue is elsewhere. I also tried to reset the PID without success. The car will start when the G28 is disconnected, but it is running fine with the G28 plugged in. However, the intermittent misfire problem continues to occur at higher RPM. The temperature sensor for the coolant (G62) shows the wrong temperature of that is -49c even after unplugging it. I also noticed that the oil gauge in the cockpit shows 2 bars when the actual pressure is zero. I'm not sure what to do, as i feel i have pretty much completely ruled out all other possibilities. But i'm worried that I may have missed something. Let me know if you have any ideas! TIA! 3. Fuel Pump The fuel pump in the g28 is activated by a signal sent by the RPM sensor. The GM-style transmitter functions similarly to the G4 sender and both work on the 80,100,200, UrS, and RS2 vehicles. It is easy to find an extra in a wrecking shop or a parts store. It is simple to test them: simply switch your DMM into resistance mode and test the distance between pins 1 and 2 (with the bump at the connector's end facing up). They must be infinite ohms. 4. ECU Our 20vt turbo (3B AAN, ABY and ADU) engines have an ECU that has to know the speed and position of the crankshaft in order to make decisions regarding timing of the fuel injectors, etc. In order to do this it uses a Crank Position Sensor (G4) and an Engine Speed Sensor (G28). If you have a problem with either one of these, the diagnostic scanner will show codes that could cause the engine shutting down. A malfunctioning G28 sensor could cause an inaccurate speed counter for the gearbox, a gearbox that shifts more quickly than normal, or an unfire when in gear. It is probable that your sensor is failing and requires to be replaced if you encounter any of these symptoms. They're inexpensive and easy to locate especially if they're a Bosch unit like ours. Alternatively, the GM version of this part is also a good choice. 5. Tachometer A damaged engine sensor could cause a myriad of issues in your vehicle. It's an essential component of the transmission in your [[https://carlocksmiths62791.humor-blog.com/29034314/7-things-about-what-is-audi-comfort-key-you-ll-kick-yourself-for-not-knowing|audi car keys]] tt key case ([[https://car-locksmiths21011.blogars.com/29087484/how-do-i-get-a-replacement-key-for-my-audi-the-ugly-reality-about-how-do-i-get-a-replacement-key-for-my-audi|mouse click the up coming post]]) because it relays information to the ECU regarding how fast or slowly the engine of the car is spinning. If this sensor fails, it could cause problems for the transmission and the rest of the car's components. (Image: [[https://g28carkeys.co.uk/wp-content/uploads/2023/10/young-couple-holding-the-keys-of-a-new-car-select-2023-04-03-23-35-08-utc-scaled.jpg|https://g28carkeys.co.uk/wp-content/uploads/2023/10/young-couple-holding-the-keys-of-a-new-car-select-2023-04-03-23-35-08-utc-scaled.jpg]])The G5 engine sensor is located near the edge of the transmission, just above the flywheel ring. It sends an electrical signal through gray wire to ECU pin T55/49. The ECU utilizes this signal to control fuel and boost, and also timig. It also sends it to the G5 Tachometer inside the instrument cluster. You can test the sensor for failure by checking continuity between it and the tachometer, between ECU pin T55/49 and the instrument cluster connection to pin T6a/1 (trace [79trace [79]) and between pin T6a/1 and the instrument cluster pin T26a/12. There should be the resistance to be around 1000 ohms between these points. This is the same across the [[https://autolocksmith98764.blog-a-story.com/9823087/is-audi-spare-key-the-greatest-thing-there-ever-was|audi tt replacement key]] 80-100-200-RS2 range, from the 1985 MC up to the 1997 UrS AN and the 1995 RS2 DU You may also find them in wrecking yards.